The wishlist name can't be left blank
HR (High Rejection) LTE/4G filter 47...782 MHz (Ch.59),

HR (High Rejection) LTE/4G filter 47...782 MHz (Ch.59), "EasyF" connection

HR (High Rejection) LTE/4G filter, with DC pass 47...694 MHz (Ch.48), "EasyF" connection

LTE/5G filter with high rejection against interference from channel 48 up. Allows DC pass from output to input. Suitable for outdoor use.
Ref. 405203
Product Sheet
EAN13: 8424450209127
SKU
405203
Highlights
  • Low insertion losses to avoid any impacts on the distributed signals
  • EasyF system: easy, quick and safe connectorization
  • Ultra-small ergonomic design
  • Fully automated manufacturing, subject to the most stringent quality controls
  • High-screening Zamak chassis

Main features
  • Resistant ABS-plastic case for outdoor installation
  • Orange colour

Discover

EasyF connection system: simplicity and savings

EasyF is an innovative connection concept where the inner conductor of the coaxial cable is directly inserted in the device, thus improving connection reliability. Thanks to the absence of F connectors, the chassis can be reduced and the connection of two cables secured with a a single screw.

  • Real time savings: speeding the installation is possible without the need for coaxial cable termination. Furthermore, there is no need for screwing the connectors on the device, which is sometimes difficult when there is little room
  • Connection reliability: the clamp holding the cables prevents the coaxial cable to come off
  • Cost savings: no additional connectors are required (neither F nor IEC)
  • Space optimization: inputs and outputs are always on the same side of the device to prevent coaxial cables from bending, and to make working inside cabinets and register boxes easier
  • Very easy three-step mounting: only screwing and unscrewing the covers is required to connect both cables:

1. Unscrew the device's cover to access the connection

2. Insert the previously stripped coaxial cables

3. Close the cover and screw to ensure connection

Learn more about EasyF system reliability

With EasyF, the connection between the coaxial cable and the device is carried out using an automated system for contact insertion of the inner conductor, without any soldering.

  • Always as new: the device's operating life increases when the factor of solder wearing out with time is removed
  • Failure rate reduction: usually produced as a result of cold soldering joints
  • Electromagnetic behaviour optimization: for high frequencies
  • Our commitment with environment is reinforced: pollution caused by the welding process is eliminated and production power consumption is reduced

Rejected bandMHz 733 ... 862
Rejected band attenuationdB > 25
Pass bandMHz 47 ... 694
Pass band attenuationdB1
Number of inputs1
Number of outputs1
Connectors"EasyF" type
DC passIn.↔Out
Max. currentmA300
Operating temperature°C -5 ... 45
Protection index23

Physical data

Net weight: 197 g

Gross weight: 197 g

Packing

Box 1 Units

Carton 10 Units

More Information
tlv_tags

EasyF connection system: simplicity and savings

EasyF is an innovative connection concept where the inner conductor of the coaxial cable is directly inserted in the device, thus improving connection reliability. Thanks to the absence of F connectors, the chassis can be reduced and the connection of two cables secured with a a single screw.

  • Real time savings: speeding the installation is possible without the need for coaxial cable termination. Furthermore, there is no need for screwing the connectors on the device, which is sometimes difficult when there is little room
  • Connection reliability: the clamp holding the cables prevents the coaxial cable to come off
  • Cost savings: no additional connectors are required (neither F nor IEC)
  • Space optimization: inputs and outputs are always on the same side of the device to prevent coaxial cables from bending, and to make working inside cabinets and register boxes easier
  • Very easy three-step mounting: only screwing and unscrewing the covers is required to connect both cables:

1. Unscrew the device's cover to access the connection

2. Insert the previously stripped coaxial cables

3. Close the cover and screw to ensure connection

Learn more about EasyF system reliability

With EasyF, the connection between the coaxial cable and the device is carried out using an automated system for contact insertion of the inner conductor, without any soldering.

  • Always as new: the device's operating life increases when the factor of solder wearing out with time is removed
  • Failure rate reduction: usually produced as a result of cold soldering joints
  • Electromagnetic behaviour optimization: for high frequencies
  • Our commitment with environment is reinforced: pollution caused by the welding process is eliminated and production power consumption is reduced
tlv_tabla_especificaciones
Rejected bandMHz 733 ... 862
Rejected band attenuationdB > 25
Pass bandMHz 47 ... 694
Pass band attenuationdB1
Number of inputs1
Number of outputs1
Connectors"EasyF" type
DC passIn.↔Out
Max. currentmA300
Operating temperature°C -5 ... 45
Protection index23
tlv_ean 8424450209127
tlv_dim_product_x 0
tlv_dim_product_x_label Width
tlv_dim_product_x_unit mm
tlv_dim_product_y 0
tlv_dim_product_y_label Height
tlv_dim_product_y_unit mm
tlv_dim_product_z 0
tlv_dim_product_z_label Depth
tlv_dim_product_z_unit mm
tlv_weight_product_label Main product weight
tlv_weight_product 0
tlv_weight_product_unit g
tlv_gross_weight_label Gross weight
tlv_gross_weight 197
tlv_gross_weight_unit g
tlv_net_weight_label Net weight
tlv_net_weight_unit g
tlv_net_weight 197
tlv_1_type_pack Box
tlv_1_type_pcs_pack Units
tlv_1_pcs_pack 1
tlv_2_pcs_pack 10
tlv_2_type_pack Carton
tlv_2_type_pcs_pack Units

Assembly and advantages of EASYF connection system