The wishlist name can't be left blank
PicoKom domestic amplifier

PicoKom domestic amplifier

PicoKom domestic amplifier

3 outputs (2+TV): VHF/UHF - LTE790 Ready

Domestic amplifier with 3 outputs (2+TV) and automatic gain adjustment to extend the terrestrial television domestic network.
The TV output provides a lower gain for direct connection to the television set (no outlet installation).
Equipped with LTE/4G filtering and input power supply for pre-amplifier or BOSS system feeding.

Ref. 560543
Generate PDF
EAN13: 8424450166604
  • Plug & Play, no adjustments required: equipped with automatic gain regulation, without any impact on signal quality
  • Pleasing design and limited size: can be installed in 100 mm x 100 mm connection boxes
  • EasyF connection system
  • Integrated high-performance switched-mode power supply: reduced power consumption (40% less than a standard amplifier)
  • Fully automated manufacturing, subject to the most stringent quality controls

Main features
  • ON/OFF DC pass switch, for pre-amplifier or BOSS system powering
  • Easy mounting, preserving the bending radius of the coaxial cables
  • Can be wall-mounted using screws


EasyF connection system: simplicity and savings

EasyF is an innovative connection concept where the inner conductor of the coaxial cable is directly inserted in the device, thus improving connection reliability. Thanks to the absence of F connectors, the chassis can be reduced and the connection of two cables secured with a a single screw.

  • Real time savings: speeding the installation is possible without the need for coaxial cable termination. Furthermore, there is no need for screwing the connectors on the device, which is sometimes difficult when there is little room
  • Connection reliability: the clamp holding the cables prevents the coaxial cable to come off
  • Cost savings: no additional connectors are required (neither F nor IEC)
  • Space optimization: inputs and outputs are always on the same side of the device to prevent coaxial cables from bending, and to make working inside cabinets and register boxes easier
  • Very easy three-step mounting: only screwing and unscrewing the covers is required to connect both cables:

1. Unscrew the device's cover to access the connection

2. Insert the previously stripped coaxial cables

3. Close the cover and screw to ensure connection

Learn more about EasyF system reliability

With EasyF, the connection between the coaxial cable and the device is carried out using an automated system for contact insertion of the inner conductor, without any soldering.

  • Always as new: the device's operating life increases when the factor of solder wearing out with time is removed
  • Failure rate reduction: usually produced as a result of cold soldering joints
  • Electromagnetic behaviour optimization: for high frequencies
  • Our commitment with environment is reinforced: pollution caused by the welding process is eliminated and production power consumption is reduced

Outputs 3(2+1TV)
-12dB @TV
Frequency margin MHz 47...400 470...790
Gain G dB 10 16
Gain adjustment range Auto 0...20
Max. output level EN 50083 IMD3 (2 tones, -35dB) Vout dBμV 105 109
DIN45004B 98 102
2 CH’s VHF DVB-T 91
10 CH’s VHF DVB-T 92
Noise figure N.F. dB 4 5
Power supply/Max.
current inputs
OFF Vdc/
ON 12/150
Mains voltage/frequency V~/Hz 196...253 / 50-60
AC power consumption W 3,7
Through current Out -> In mA -
Protection index IP 20
Operating temperature range ºC -5 ... +45

Not always. Among the devices provided with the Dinova antenna, there is actually a power supply unit. In case of an installation that includes distribution, an active power supply may be required, since the gain it provides allows for the distribution of the signal towards multiple reception points. However, for installations involving just a receiver and an adapter (portable installations), a zAs adapter could power the Dinova antenna without the need for an extra power supply.