The wishlist name can't be left blank
Streamer with remultiplexing

Streamer with remultiplexing

Streamer with remultiplexing

Streamer with remultiplexing

Streamer with remultiplexing

DVBS/S2 - IP, with CI

Streamer generating an IP encapsulated output from the multiplexing of the services available in up to 3 different TV SAT transponders.

These may be extracted from 2 different satellites (2 independent SAT inputs), or from a single satellite, using the headend's input loop.

The encrypted satellite channels are transformed into free IP services through the CI interface and the appropriate CAM module. Depending on the CAM type used (standard/professional), one or several services may be opened for free visualization.

The system will encompass a power supply and some streamer modules depending on the number of services to be distributed.

Ref. 565801
Generate PDF
EAN13: 8424450209073
SKU
565801
Highlights
  • 32 IP streams SPTS
  • DiSEqC 1.0 for multiswitches control
  • Service decryption by insertion of a PCMCIA module
  • Access to the headend configuration through a self-created WiFi network (using the kit with ref.216802)
  • Internal switch for IP out Daisy chain of serveral modules
  • External to the headend services signaling, such as those coming from a HE-21 headend
  • Equipment monitoring using basic SNMP protocol, which allows behavior values to be indicated through the network (network information, unit turn-on times, etc ...)
  • Embedded user web interface for module configuration:
    • Configuration of the entire headend selecting one of the module as a master
    • Automatic detection of the modules that are connected to the master
    • Cloning function to replicate configurations between modules and headends
    • UDP or RTP output protocol selection, for greater compatibility with IPTV sistems
    • Headend control indicators: module temperature, CAM status ...

Main features
  • Selection of services among the 3 input transponders to distribute in streaming
  • Includes EPG information (Electronic Program Guide) in the headend output stream
  • Provides flow information of each service to estimate the global output flow of the module
  • Device monitoring and signal status LEDs

SATELLITE
DEMODULATOR
Input frequency
MHz 950...2150
Symbol rate
Mbaud 2 - 45
 Frequency steps MHz 1
 In/Out connectors tipo “F” female
 Input impedance Ω 75
 LNB powering
Vdc/KHz 13 - 17 - OFF / 22KHz (ON-OFF)
 Satellite selection (DiSEqC) Port A, B, C, D
 Through losses (typ.) dB < 1,5
 Modulation
DVB-S2 QPSK, 8PSK
DVB-S QPSK
 FEC inner code LDPC 9/10, 8/9, 5/6, 4/5, 3/4, 2/3, 3/5, 1/2
 FEC outer code Bose-Chaudhuri-Hocquenghem
 Roll-Off factor % 20, 25, 35
Input SWR (min.)
dB 10
 IP OUT
 Mode Multicast/Unicast
 Format SPTS
 Protocol
IPv4, UDP/RTP, DHCP
 Number of IP services
Max. 32
 Connectors 2 X RJ45 (1 GB Ethernet 1000 BaseT)
 GENERAL  Consumption 24Vdc (Base+CAM+LNB)
mA 1050 (450+100+250/LNB)
 Protection index
IP IP20
 Temperature range
ÂşC 0...45

Remultiplexing of services

The unit has three demodulators (TS A, TS B, TS C) that, depending on how the loop mode is configured, one or two bands and polarities should be available for all demodulators. In the second case, the first connector will deliver to TS A and the second to TS B and TS C.

Programming of the entire headend selecting one of the module as a master

Configure one of the modules as a master of the entire headend. Any module can be selected as the master. Once the master mode is activated, the unit searches for other units connected to the network (ETH2).

The units can be visually ordered in the web interface to identify them more easily with the real position in the headend. Each of the modules can be identified by temporarily activating the flash of the front LED.

Multiple addition of services

Multiple services can be added at once by selecting one base IP address and one base port, such as the wanted services, and an IP address or port auto-increment The web interface will automatically generate rhe IP multicast addresses of each of the services, in terms of the selected parameters.

Separated networks in each module

Each unit has two Ethernet RJ45 connectors, which can be used on an single network or on two separate networks, one for control and the other for video distribution. Users can be enable the separation of these networks (Split Net Ports) and configure the IP address, subnet mask, and default port link, as well as the DHCP client mode.

Cloning of headends configurations

The web interface allows to export/import files for duplicating units (or complete headends) configurations. This function helps to reduce time in typical installations, due of having previously a configured file. The exportation of these files also allows to have a headend configuration backup.

Status reports generation

Users can download report files on the selected unit, or of the complete headend, to make easier debugging in the event of an incident.

Block diagram