24V-5A power supply

For several modules, 196-264Vac

Flyback-type, high-power and high-performance (>85%) switched-mode power supply . Provides 5A at 24V (120W).

Ref. 5629

Codes

Generate PDF

EAN13: 8424450139295

SKU

5629

Televes reserves the right to modify the product

Main features

Equipped with two outputs monitored by LED diodes that indicate the status of the provided voltages
Overload and short-circuit detection
Maximum current limited to 4A per output
Equipped with protection against output-voltage variation

Mains frequency	Hz	50 / 60
Max. input current	(A~)	1,35 (5929) / 1,5 (593901)
Output voltage	(V=)	24
Max. output current	(A=)	5
Max. output power	W	120
Max. operating temperature	ºC / ºF	45 / 113
Protection index	IP	IP 20

How many modules can T0X power supply units feed?

As a general rule, they can power up to 7 modules. However, the actual number depends on the type(s) of the T0X modules being used; that is why it is always recommended to check the instructions manual of the specific equipment for the answer.

T0X power supply units have two outputs. Do both have to be used?

Yes, for load balancing purposes. One of the outputs can serve up to 4 equipment, the other up to 3 equipment (to average 7)

How can I add an IF signal to a DTT-only T.0X processing headend and transmit it through an optical fibre to distant spots?

In some cases, the transmodulation of specific satellite channels into COFDM will probably not be enough; this is why the option is available to add the IF of a satellite polarity to the COFDM signal flow. Furthermore, that signal flow may be transmitted over optical fibre by means of an appropriate low-loss optical transmitter, thus allowing to reach longer distances.

1. T.0X processing headends (DVB/S2-COFDM and DVB-T/COFDM transmodulators, encoders/modulators, amplifier, etc.).

2. MiniKom amplifier ref. 5363 (Art. No. EV45).

3. SMATV optical transmitter ref. 238201 (Art. No. OMS1310).

4. SMATV optical receiver ref. 2311 (Art. No. OE1216)

How many T.0X modules can I install in my housing and frames?

Thanks to these measures and graphics, you will be able to know how many modules you can fit in each cabinet or frame. Televes uses standard dimensions in order to make installation easier for our technicians. These dimensions are taken from a Eurocard (standard European format for PCB). Vertically, we find the U (Unit Rack) equivalent to 1.75 inches (44.45 mm), horizontally we have the HP (Horizontal Pitch), equivalent to 0.2 inches (5.08 mm).

Below you will find the dimensions of the main modules in our headend series.

Supports and Cabinets		HP
5301	19’’ Rack frame	84
567201	19’’ Wall support	54
5072	Lockable Cabinet 498mm	84
5069	Lockable Cabinet 648mm	112
5235	Lockable Cabinet 948mm	168

Equipment dimensions’ list		HP
5629 549812	Power Supply Unit (T.0X/T.12)	14
-	T.0X (Transmodulators, CDC,... normal chassis equipment)	10
-	T.12	7
5673	T.0X Blank Plate	10
507312	T.12/T.05 Blank Plate	7

Optical fibre		HP
234220	T.0X EDFA	14
2337 2339	T.0X Splitter 2D/4D	10
234401 234501 234601	T.0X Splitter 8D/16D/32D	18
234228	T.0X EDFA 1E/8S	22

Rack mount.

Block diagram